Built-Up Roofing in San Francisco: Cost, Layers, Lifespan (2026)

Key Facts
- A built-up roof (BUR) is 3 to 5 alternating layers of bitumen and reinforcing felt, finished with gravel or a mineral cap sheet.
- Bay Area planning cost: $9 to $14 per sq ft installed. A 1,500 sq ft roof runs about $13,500 to $21,000.
- Lifespan: 15 to 30 years with proper installation and maintenance. 20 to 30 years is the usual figure for a well-built 4-ply system.
- A 4-ply gravel membrane weighs about 5.5 to 6.3 lbs per sq ft. The gravel alone is about 4 lbs per sq ft.
- BUR is a commercial system first. It also fits flat residential additions, garages, and low-slope sections in the Sunset and Richmond.
- San Francisco permits start at $514 for a single-family or duplex reroof and $714 for other buildings. Hot asphalt work needs an SFFD permit and a firewatch.
Quick Answer
A built-up roof, or BUR, is a flat or low-slope roof made on site from alternating layers of hot or cold bitumen and reinforcing felt, finished with gravel or a mineral cap sheet. It has protected American buildings for more than 100 years. In San Francisco, plan on $9 to $14 per sq ft installed, a lifespan of 15 to 30 years, and a 4-ply gravel assembly that weighs about 6 lbs per sq ft. BUR wins when the roof takes heavy foot traffic, holds HVAC equipment, or needs to last decades.
What Is a Built-Up Roof?
A built-up roof is a membrane built up on the roof itself, one layer at a time, instead of unrolled from a factory. The roofing manufacturers association defines it as multiple layers of asphalt alternated with ply sheets, called felts, over the roof deck and usually over insulation. The common name is tar and gravel, because the classic finish is a flood coat of asphalt with gravel embedded in it.
BUR arrived in the mid-1800s and was the first real flat roofing system. No single layer has to be perfect, because three to five layers back each other up. You will see BUR on the flat roofs San Francisco was built with: warehouses in SoMa (94103), Dogpatch (94107), and Bayview (94124), and flat-roofed homes in the Sunset (94122) and Richmond (94121). It is a commercial system first, but it also fits a flat garage, a rear addition, or a low-slope section on a house. BUR is not the same thing as roofing tar. Tar is one ingredient. Our guide to roofing tar in San Francisco covers the material itself.
How a Built-Up Roof Is Built, Layer by Layer
A BUR is a stack, and every layer has a job. From the bottom up:
Roof deck. Wood, concrete, or steel. It must be solid, dry, and strong enough for the finished weight.
Vapor retarder. Stops interior moisture from rising into the assembly. Kraft paper or a foil-faced sheet are the usual choices.
Insulation. Usually two layers of rigid polyiso with staggered joints. Polyiso gives about R-5.6 per inch, so R31 is about 5 to 6 inches.
Base sheet. The first sheet, mopped or fastened down. It gives the first mopping something to bond to.
Ply sheets. Three or four reinforcing felts, each set in its own bed of hot bitumen and offset so no two joints line up. The crew starts with narrow stripping plies, 12 inches, then 24 inches, then full 36-inch rolls, so water runs over the joints, not against them.
Flood coat and surfacing. A flood coat of asphalt, about 60 to 70 lbs per 100 sq ft, with pea gravel embedded in it. The gravel is the UV shield, the traffic armor, and the ballast, and it gives the assembly its fire rating, since stone does not burn.
The finished membrane is about half an inch thick without the gravel. Every ply is fully bonded to the next, so there are no seams to peel. To check an existing roof, pull up a vent or take a core cut and count the plies.
The Three Types: Hot, Cold, and Ballasted
Hot-applied BUR. The classic method. Asphalt is heated in a kettle to about 450 to 500 degrees and mopped between the plies at roughly 20 to 25 lbs per 100 sq ft. It needs to be thin enough to wet the felt, about the consistency of motor oil. Too cool and it does not bond. Too hot and it thins out. A kettle man stays with the kettle the whole job, because it is propane-fired and the asphalt can catch fire.
Cold-applied BUR. The same layering, but the bitumen is a cold adhesive spread with a notched squeegee at about the same rate, roughly 25 lbs per 100 sq ft. No kettle, no fumes, no burn risk, and the building can stay occupied. The trade-offs are cost, about 10 to 20 percent more, and weather sensitivity.
Ballasted BUR. The lower layers are laid loose, and heavy stone holds the whole assembly down. It suits a strong deck on a large, simple roof. It is not a shortcut for a weak structure.
How Much Does a Built-Up Roof Cost in San Francisco?
National 2026 guides put BUR at $4 to $14 per sq ft installed, with most sources clustering at $5 to $10. Texas pricing from September 2026 runs $7.50 to $10. Those are national numbers, and San Francisco labor and access run higher than the national average.
For the Bay Area, plan on $9 to $14 per sq ft installed for a 4-ply gravel BUR with code insulation. That is a planning figure, not a quote. A 1,500 sq ft roof runs about $13,500 to $21,000. Before you sign, read our guide to how to read a roofing quote.
How Long Does a Built-Up Roof Last?
The consensus across 2026 guides is 15 to 30 years. Nations Roof gives 20 to 30 years with proper installation and maintenance. Fixr gives 15 to 30. One commercial guide gives 20 to 30. One contractor guide claims 15 to 40 years, but that is the outlier high end and it assumes a warm climate. In San Francisco, 20 to 30 years is the honest planning figure for a well-built 4-ply system.
What shortens the life: ponding water, poor drainage, trapped moisture, skipped maintenance, and bad flashings. Most leaks start at the edges and penetrations, not in the field of the roof.
Built-Up Roofing vs Modified Bitumen
Modified bitumen is BUR’s modern cousin: a factory-made sheet of asphalt with polymers added for flexibility, in two plies, a base sheet and a granulated cap sheet. BUR is built up on the roof from three to five plies of felt and bitumen. Our full comparison of the two modified bitumen types is in SBS vs APP modified bitumen in San Francisco.
| Feature | Built-Up Roofing (BUR) | Modified Bitumen |
| Layers | 3 to 5 plies built on site | 2 plies, factory-made sheets |
| Redundancy | Highest, one ply can fail and the rest hold | Good, two plies |
| Flexibility | Stiff, does not move with the building | Flexible, handles movement and temperature cycles |
| Installation | Hot kettle or cold adhesive, slow | Torch, cold adhesive, or self-adhered, faster |
| Fire risk during install | Kettle fire risk, needs a firewatch | Torch fire risk, needs a firewatch |
| Foot traffic | Best in class | Good |
| Leak finding | Hard, layers hide the source | Easier, fewer layers |
| Weight | Heaviest, about 6 lbs per sq ft for 4-ply gravel | Lighter |
| Best for | Long-term commercial roofs, heavy traffic, solar platforms | Smaller roofs, occupied buildings, faster jobs |
Choose BUR when the roof is a long-term asset, takes heavy traffic, or carries equipment and solar. Choose modified bitumen when the building moves, the schedule is tight, or the roof is small.
Built-Up Roofing vs TPO, EPDM, and PVC
BUR is the oldest system on this list by a century. TPO arrived in the late 1990s, and EPDM and PVC date to the 1960s. All four can last 20 to 30 years. For the small-roof alternative, see torch-down roofing cost in San Francisco.
| System | Bay Area installed cost | Lifespan | Weight | Foot traffic | Best for |
| Built-up roofing | $9 to $14 per sq ft | 15 to 30 years | About 6 lbs per sq ft | Best | Heavy traffic, long-term roofs |
| Torch-down modified bitumen | $8 to $13 per sq ft | About 20 years | Moderate | Good | Small flat roofs, fast jobs |
| TPO | $7 to $11 per sq ft | 20 to 30 years | Light | Moderate | Energy savings, budget reroofs |
| EPDM | $8 to $14 per sq ft | Up to 30 years | Light | Moderate | Cold flexibility, simple roofs |
| PVC | $10 to $16 per sq ft | 20 to 30 years | Light | Moderate | Restaurants, grease, chemicals |
TPO wins on energy: a white TPO surface reflects up to 87 percent of UV. BUR with gravel absorbs heat. EPDM and PVC are single sheets, so a puncture is a leak. A BUR puncture is usually just a damaged top ply. Read our EPDM roofing guide and PVC roofing guide for the full comparison.
Weight: The Number Nobody Checks First
BUR is the heaviest low-slope system, so the weight is the first thing to check on an older building. A 4-ply gravel membrane weighs about 5.5 to 6.3 lbs per sq ft from manufacturer data sheets, or 550 to 630 lbs per roofing square. The gravel alone is about 4 lbs per sq ft, because the building code requires a minimum of 400 lbs of gravel per square. A smooth 4-ply membrane without gravel is about 2.6 lbs per sq ft.
A 1,500 sq ft roof carries about 8,250 to 9,450 lbs of membrane, and about 6,000 lbs of that is gravel. That weight is why BUR holds up under foot traffic, wind, and hail, and it is why a structural engineer must confirm the deck can carry it before you replace a light single-ply roof with a gravel BUR. Older wood-framed buildings in the Sunset and Richmond, and lightweight steel decks in SoMa warehouses, sometimes cannot take the extra load without reinforcement. Every recover adds another full assembly. One building-owner post that drew thousands of votes described a roof measured at 35 inches thick after decades of recoveries.
Built-Up Roofing in San Francisco: Fog, Salt Air, and Rain
The marine layer keeps summer temperatures mild, so the asphalt does not bake the way it does inland. That is good for lifespan. The fog also keeps roofs damp for long stretches, and damp is what moss and algae need.
Salt air is the second factor. Buildings near the coast, in the Sunset, Richmond, and Bayview, get salt spray on every surface. BUR itself does not corrode, because it has no exposed metal and no fasteners.
Rain is the third factor, and it is seasonal. Almost all of it falls from November to March, often in hard bursts. A BUR that drains well handles it easily. A BUR with a clogged drain or a sagging low spot does not, because the water has nowhere to go. The fix is slope, not more layers. The kettle is the trade-off: hot asphalt smells, and the smell reaches the neighbors.
Ponding Water: The 48-Hour Rule
Ponding is any water that stays on the roof longer than 48 hours. It is the single most common reason a BUR fails early, and it is a maintenance item, not a warranty item. One inch of water weighs 5.2 lbs per sq ft. A 10 by 10 foot pond one inch deep weighs 520 lbs. A 20 by 20 foot pond one inch deep weighs 2,080 lbs. That weight sags the deck, the sag deepens the pond, and the pond collects more water, dirt, and debris. A BUR handles a little standing water better than a single-ply roof. It does not handle a permanent pond. The fix is drainage first: clear the drains, check the scuppers, and add tapered insulation for slope toward the drain. Our full guide to ponding water on flat roofs in San Francisco covers the inspection and the fixes.
Permits, Title 24, and the Firewatch Rule
A BUR reroof in San Francisco needs a building permit, starting at $514 for a single-family home or duplex and $714 for all other building types, with additional fees on top. Only a licensed C-39 contractor can apply online. Our full guide to roofing permits in San Francisco has the full process.
Hot work is the second rule. A kettle of asphalt at 450 to 500 degrees is an open fire risk. San Francisco Fire Department rules require a permit for hot roofing work and a dedicated firewatch: one person, with a phone and an extinguisher, on site during the work and for one hour after it stops.
Title 24 is the third rule. San Francisco is in Climate Zone 3. For nonresidential low-slope roofs, the 2025 standards call for an aged solar reflectance of 0.63 and a thermal emittance of 0.75, which a dark gravel BUR does not meet on its own. Three options make it compliant: an aluminum or white reflective coating, a white granulated cap sheet, or white gravel. Our guide to commercial roof insulation and Title 24 has the full requirements.
Repair, Recover, or Replace?
Repair. A blister is cut open, dried, and patched with two plies; a split is sealed with mastic; a flashing is resealed. The hard part is finding the leak, because water travels between the plies and shows up far from where it entered. That is why roof leak detection in San Francisco starts with the penetrations and flashings, not the middle of the field. One experienced installer puts it at 95 percent of leaks starting at a penetration or a flashing. That is a creator claim, not a measured statistic.
Recover. A recover, or overlay, puts a new system over the old one. It is only safe when the old roof is dry. Scan for wet areas with infrared first, cut out and replace the wet sections, then recover the dry remainder. Never recover over wet insulation. The trapped water rots the assembly, kills adhesion, and can let wind lift the new roof off.
Replace. A tear-off is the right call when the insulation is wet across the roof, the deck is damaged, the roof has already been recovered twice, or the structure cannot carry another layer. A roof coating can buy time on a smooth BUR that is sound but weathered, but a coating is not a new roof and it does not fix wet insulation.
What to Check While the Crew Works
Most BUR failures are installation failures, and most of them are visible while the work is happening. A user post with dozens of replies described a crew that forgot the primer and polyester mesh over the base sheet and only noticed after the coating was on. Check the mopping coverage, the asphalt temperature near 450 degrees, the flashings, the gravel coverage, and the drain sump while the crew works.
Frequently Asked Questions
What is a built-up roof (BUR)?
A flat or low-slope roof made on site from 3 to 5 alternating layers of bitumen and reinforcing felt, finished with gravel or a mineral cap sheet.
How much does a built-up roof cost in San Francisco?
Plan on $9 to $14 per sq ft installed in the Bay Area for a 4-ply gravel BUR with code insulation. A 1,500 sq ft roof runs about $13,500 to $21,000.
How long does a built-up roof last?
15 to 30 years with proper installation and maintenance. 20 to 30 years is the usual figure for a well-built 4-ply system.
How many layers does a built-up roof have?
Three to five plies, with four plies as the standard commercial specification. Each ply is a felt set in its own bed of bitumen, offset so no two joints line up. A core cut confirms the true ply count.
Is a built-up roof the same as tar and gravel?
Tar and gravel is the gravel-surfaced type of built-up roof. BUR is the whole system.
Can you put a built-up roof on a house in San Francisco?
Yes, on a flat or low-slope section such as a rear addition, a garage, or a flat-roofed home in the Sunset or Richmond.
How heavy is a built-up roof?
A 4-ply gravel membrane weighs about 5.5 to 6.3 lbs per sq ft, or 550 to 630 lbs per roofing square. The gravel alone is about 4 lbs per sq ft.
Does a built-up roof need a permit in San Francisco?
Yes. A reroofing permit starts at $514 for a single-family home or duplex and $714 for all other building types, with additional fees. Only a licensed C-39 contractor can apply online.
Can a built-up roof be a cool roof under Title 24?
A dark gravel BUR cannot meet the cool roof standard on its own. It can comply with an aluminum or white reflective coating, a white granulated cap sheet, or white gravel.
How do you find a leak in a built-up roof?
Start at the penetrations and flashings, not the middle of the field, because that is where most leaks begin. Then use core cuts and an infrared scan to find wet insulation and trace the water path.
Can you recover, or overlay, a built-up roof?
Yes, but only when the old roof is dry. Scan for wet areas with infrared first, cut out and replace the wet sections, then recover the dry remainder. Never recover over wet insulation.
Built-up roofing vs modified bitumen: which is better?
BUR is better for long-term commercial roofs, heavy foot traffic, and roofs that carry equipment or solar. Modified bitumen is better for smaller roofs, occupied buildings, and faster jobs.
Bottom line
A built-up roof is the oldest flat roofing system still in common use, and it is still the toughest one for a roof that takes traffic, equipment, and decades of weather. In San Francisco, plan on $9 to $14 per sq ft, 15 to 30 years of life, and a 4-ply gravel assembly at about 6 lbs per sq ft. Get the drainage, the permit, the firewatch, and the weight check right, and never recover over wet insulation.
NAICS Code 238160 – Roofing Contractors. For a detailed inspection of your flat or low-slope roof in San Francisco, call +1 833-804-6249.
