PVC Roofing San Francisco | Cost, Lifespan & Installation

Key Facts
- PVC (polyvinyl chloride) is a heat-welded single-ply membrane, 50/60/80 mil thick, built to ASTM D4434.
- Bay Area installed cost: 10–16 per sq ft; a 1,500 sq ft roof runs 15,000–24,000 before tear-off.
- Lifespan: 25–30 years at 60 mil; 20–25 at 50 mil; 25–30+ at 80 mil.
- Best for: restaurants and commercial roofs where kitchen exhaust grease or chemicals reach the roof; flat and low-slope roofs below 2/12.
- SF permits: $514 and up (single-family/duplex), $714 and up (other buildings). Title 24 cool-roof rules apply.
- Call +1 833-804-6249 for a detailed inspection.
Quick Answer
PVC roofing is a single-ply plastic membrane whose seams are welded with hot air until they become one piece. In San Francisco it costs $10 to $16 per square foot installed, lasts 25 to 30 years at 60 mil, and is the standard choice wherever kitchen exhaust grease or chemicals reach the roof. It runs 20 to 30 percent more than TPO. Below a 2/12 slope, PVC and TPO are the only real options, and shingles or metal installed there void the warranty.
How Much Does PVC Roofing Cost in San Francisco?
In the Bay Area, plan on $10 to $16 per square foot installed for a standard 60-mil PVC system. National guides put PVC at $7 to $15 per square foot installed, and 60-mil systems at $9 to $15. A 1,500 square foot roof runs $15,000 to $24,000 at the Bay Area figure, before tear-off.
Tear-off adds $1 to $2.50 per square foot. Tapered insulation, which fixes ponding, adds more. Small jobs cost more per square foot, sometimes up to 50 percent more, because the crew and the equipment cost the same on any size roof.
| What you pay for | Cost |
| PVC installed, Bay Area planning figure | 10–16 per sq ft |
| 1,500 sq ft roof, Bay Area figure | 15,000–24,000 |
A reported quote from Southern California shows how much scope matters. A homeowner with a 750 to 900 square foot flat roof was quoted $8,360 for a PVC recover over a single layer of peel-and-stick, which works out to $9.29 to $11.15 per square foot. Four other quotes ran $14,500 to $22,000, but every one included tear-off, priced at $6,000 alone because the building is three stories with no roof access. The cheap quote was not a bad quote. It was a different job. Compare the scope line by line, not the bottom number. Our guide to how to read a roofing quote walks through the full checklist.
PVC Roofing Thickness: 50, 60 or 80 Mil?
Thickness is the single biggest variable in how long a PVC roof lasts, bigger than the brand on the roll. PVC membranes come in 50, 60 and 80 mil, and the standard, ASTM D4434, requires at least 16 mils of material over the reinforcement scrim. That layer is what the sun, the fog and the foot traffic wear away.
For most commercial work in San Francisco, 60 mil is the practical minimum. It carries the 25-year warranties. Fifty mil is the budget option: cheaper, but it gives up about five years. Eighty mil is the premium choice, with the longest warranties and the best puncture and hail resistance. KEE membranes, built to ASTM D6754, resist the brittleness standard PVC develops with age, and they carry the longest warranties in the category, up to 35 years on 80-mil certified systems.
| Thickness | Lifespan | Manufacturer warranty |
| 50 mil | 20–25 years | Up to 20 years |
| 60 mil | 25–30 years | Up to 25 years |
| 80 mil | 25–30+ years | Up to 30 years |
How PVC Roofing Is Installed in San Francisco
PVC goes down three ways: mechanically attached, fully adhered, or induction-welded. Mechanically attached is the most common on commercial roofs. Fully adhered costs more and holds better in wind, but the adhesive has to flash off first, or solvents get trapped and blisters form. All three end the same way: hot-air welded seams, stronger than the membrane itself.
Three details separate a good PVC install from a callback. The first is the separation layer. PVC must not sit directly on asphalt-based products. Over a granulated peel-and-stick roof, which sits under half the flat roofs in the Sunset and the Richmond, a separation layer is required, anything from 6-mil plastic to a 1/4-inch overlay board. Fire-rated modified bitumen is not a separator for PVC.
The second is tapered insulation. Ponding is standing water still there 48 hours after the rain stops, and the fix is a slope built from tapered pieces. That slope has to be planned in advance: the pieces are ordered for specific places on the roof. A roofer who says they will figure it out when they get there has no plan. A small tapered section runs about $500, according to one owner’s report. Our guide to ponding water on flat roofs covers the full fix.
Third, the detailing. Parapets, scuppers, pipes and skylights are where PVC roofs leak, not the middle of the field. Termination bars hold the membrane at expansion joints. Cut edges need sealant, and missing sealant voids the warranty. Below 50 degrees Fahrenheit, nobody should walk on a PVC roof, because the membrane can shatter under foot traffic in the cold.
PVC vs TPO vs EPDM: Which Single-Ply Wins?
PVC, TPO and EPDM are the three single-ply membranes you will be quoted for a flat roof in San Francisco. Torch-down is the fourth option, still the incumbent on small residential roofs. It costs $8 to $13 per square foot installed.
| Factor | PVC | TPO | EPDM |
| Installed cost per sq ft | 10–16 | 7–11 | 8–14 |
| Lifespan | 25–30 years | 18–25 years | 20–30 years |
| Seams | Heat-welded | Heat-welded | Taped, not welded |
| Grease and chemicals | Excellent | Poor | Fair |
| Best for | Restaurants, commercial | Clean roofs, budget | Large low-slope, budget |
If kitchen exhaust grease, oils or chemicals reach the roof, PVC wins and it is not close: grease softens TPO and attacks its seams. If the roof is clean, TPO wins on value, installing 20 to 30 percent below PVC.
A reported case from a multi-unit condo makes the point. The building needed a full tapered system and the roof had plenty of contours, so the roofer recommended PVC for its flexibility. The price gap was $7,000. The owners chose TPO, and a year later they report no leaks and no pooling. PVC would have bought flexibility and extra years, not a drier roof. Where TPO loses ground is age: older TPO gets hard to weld to as the elastomers break down, while PVC can still be welded and patched decades later. There is also a middle path roofers report: an 80-mil TPO system with a 25- or 30-year warranty and a hail rider, still cheaper than PVC. Our EPDM roofing guide covers the third single-ply in depth.
PVC Roofing for Restaurants and Commercial Buildings
PVC is the restaurant roof. Kitchen exhaust carries grease, animal fats and oils onto the roof, and grease destroys TPO and EPDM. PVC is the membrane that survives it. That is why the city’s restaurant rows in the Mission (94110), North Beach (94133), SoMa (94103) and the Embarcadero (94111) are full of white PVC roofs.
A grease-exposure assembly costs more than a standard PVC roof, because the detailing around the exhaust is heavier. A 2026 guide from another market puts a restaurant grease-exposure PVC assembly at $12 to $20 per square foot installed. Bay Area pricing will differ. PVC is also the most fire-resistant single-ply membrane, carrying a Class A rating under UL 790. For the insulation and cool-roof side of a commercial job, see our commercial roof insulation and Title 24 guide.
Permits and Title 24: What San Francisco Requires
A PVC reroof in San Francisco needs a permit, and the fee is the starting total, not the whole cost. The city charges $514 and up for a single-family home or duplex, and $714 and up for all other building types, with additional fees on top. Only a licensed C-39 contractor can apply online. The one exemption is narrow: reroofing 25 percent or less of the roof surface in any 12 months, without installing, repairing or removing roof material.
Title 24 is the second rule, and it is where PVC earns its keep. The 2025 standards took effect on January 1, 2026. San Francisco sits in Climate Zone 3, and for nonresidential low-slope roofs the standard calls for an aged solar reflectance of 0.63 and a thermal emittance of 0.75. White PVC is a cool-roof membrane that meets those numbers. The alteration trigger is more than 50 percent of the roof area or more than 2,000 square feet, whichever is less. Confirm the Title 24 position in writing before the job starts. Our roofing permits guide has the fee history and the inspection steps.
PVC Roof Problems: What Goes Wrong and How to Spot It
- Blisters and bubbling. The most common complaint on a new fully adhered roof. The cause is usually adhesive that had not fully flashed off before the sheet went down, so solvents got trapped under the membrane. Most blisters disappear as the roof warms up. The pinch test decides: if you can pinch a blister together with your fingers, cut it out and patch it. Check for debris underneath first, because debris never settles, and tell the manufacturer rep.
- Cold welds. Seams that got hot enough to stick but never fully bonded. They look like a proper weld, which makes them dangerous: they pop open later.
- Freeze-thaw damage. Moisture wicks into the cut edges of a reinforced membrane. The roofer is supposed to seal every cut edge, and missing sealant voids the warranty.
- Shrinkage and chalking. As PVC ages, plasticizers migrate out and the membrane gets stiffer. Chalking, a white powdery residue, means UV is breaking the plasticizers down. KEE membranes resist this better than standard PVC.
- Scuppers and joints fail first. Unreinforced joints are the weak point of any flat roof, and on PVC the scuppers go first.
- Ponding. Standing water 48 hours after rain is ponding. Tapered insulation is the fix, planned before the job starts.
- Hail. PVC gets brittle with age, and hail is its worst enemy. One reported case had a 2018 fleeceback PVC roof on a school cracked by 1/4-inch hail and replaced, with the manufacturer paying on a materials-only warranty. A 1/2-inch cover board brings the assembly up to UL 2218 Class 3 or 4 impact ratings.
When a leak does appear, find it first. Our roof leak detection guide covers the method, and flat roof repair in wet weather covers what can and cannot be fixed while it is raining.
PVC Roofing Brands and Warranties
The brands you will see on PVC quotes in the Bay Area are Sika-Sarnafil, Carlisle Sure-Flex, Versico, GAF EverGuard, Duro-Last, Fibertite and IB Roof Systems. A recent poll of roofing pros put Carlisle and Versico first (20 of 73 votes), then Sika-Sarnafil (15), GAF (14), Duro-Last (13), Fibertite (6) and IB (5). That is a poll, not a quality ranking.
Duro-Last is the brand that splits installers. Some will not use it and say so plainly. Others say the product is fine and the problems come from installers, because anyone can buy it and the detailing only has to be watertight, not pretty. Judge the installer, not the label. What matters more than any brand is whether the installer is certified, because the long warranties are only available through certified crews.
The warranty reality surprises most owners. On a single-family home, manufacturers give a material-only warranty. There is no manufacturer workmanship warranty on a house. The workmanship warranty comes from the contractor, and a 10-year workmanship warranty is unusually long: the typical commercial figure is 2 years on a new full system and 1 year on repairs, and the longest one experienced roofer reports ever giving is 5. Our guide on how to choose a roofing contractor in San Francisco covers certification and vetting.
How to Read a PVC Roofing Quote
Check each quote against this list before you compare prices.
- Thickness in writing. 60 mil minimum for most commercial work.
- Recover or tear-off, and separation layer. How many layers are underneath, whether the old roof stays or goes, and whether a separation layer is listed over peel-and-stick or asphalt.
- Tapered insulation plan. Named, measured and priced, not “we will see on site.”
- Product name spelled right. Sure-Flex is PVC and Sure-Weld is TPO. A quote that mixes them up was copied from another job.
- Warranty terms in full. Material-only or full system, and who backs the workmanship.
- A core or test cut before work starts. It finds wet insulation and bad decking before they change orders.
Compare the scope line by line. The reported $8,360 quote and the $14,500 to $22,000 quotes for the same roof were different jobs, one a recovery and the rest tear-offs. When the scope matches and the price still differs by half, that is the red flag.
PVC Roof Maintenance in San Francisco
San Francisco is kind to PVC in one way and hard on it in another. The marine layer and fog keep peak roof temperatures down, so the membrane ages slower here than inland. But salt air and wet winters work on the seams and sealant, and the November-to-March rainy season is when every weak detail shows itself.
A PVC roof needs a detailed inspection once a year, with the drains and scuppers cleared before the rains start. Check the seams and the cut-edge sealant, and keep the membrane clean, because dirt cuts reflectivity. PVC is not a roof you coat when it gets old. When the membrane is done, the answer is a recover or a replacement, and our best roof coating guide explains when a coating is the right call instead.
Frequently Asked Questions
How much does PVC roofing cost in San Francisco?
Plan on $10 to $16 per square foot installed for a standard 60-mil system. A 1,500 square foot roof runs $15,000 to $24,000 before tear-off.
How long does a PVC roof last in San Francisco?
Twenty-five to 30 years at 60 mil, 20 to 25 at 50 mil, and 25 to 30-plus at 80 mil. Ponding, bad seams, and skipped maintenance shorten life.
Is PVC better than TPO roofing?
It depends on the roof. PVC is better wherever kitchen exhaust grease, oils or chemicals reach the membrane. TPO is better on a clean roof where budget matters, installing 20 to 30 percent below PVC.
Is PVC worth $7,000 more than TPO?
Sometimes. In one reported condo case, the owners chose TPO over PVC, saved the $7,000, and report no leaks and no pooling a year later. Pay the premium when the roof faces grease or chemicals.
Can PVC roofing go over an existing roof?
Yes. Most codes allow two layers, so a recover over a single sound layer is common. A separation layer is required over peel-and-stick or asphalt-based products. Get a core or test cut first.
What thickness should I get?
Sixty mil for most commercial work. It carries the 25-year warranties. Take 80 mil for a roof that gets walked on or holds HVAC units. Fifty mil is the budget option.
Is Duro-Last PVC good or bad?
Installers disagree, and both sides are on the record. Some say it is the worst membrane you can put on a building. Others say the product is fine and the problems come from installers. Judge the installer and the certification, not the label alone.
What are the red flags in a PVC roofing quote?
No thickness named in writing. No tapered insulation plan, only “we will see on site.” A product name that does not match the membrane, like Sure-Weld, which is TPO, on a PVC quote. A 10-year workmanship warranty with no explanation of who backs it.
Does a PVC roof need tapered insulation?
Only if water ponds. Ponding is standing water still there 48 hours after the rain stops. Tapered insulation builds the slope that drains it.
How do you fix blisters on a new PVC roof?
Most blisters are trapped solvent from adhesive that had not flashed off, and they disappear as the roof warms up. Use the pinch test: if you can pinch a blister together, cut it out and patch it.
Does PVC roofing work for restaurants?
Yes, it is the standard choice. Kitchen exhaust grease destroys TPO and EPDM, and PVC is the membrane that survives it. The Mission, North Beach, SoMa and the Embarcadero are full of PVC restaurant roofs.
Do I need a permit for a PVC roof in San Francisco?
Yes, for anything over a small repair. The city charges $514 and up for a single-family home or duplex, and $714 and up for all other buildings, with additional fees. Only a licensed C-39 contractor can apply online.
Bottom line: PVC is the right membrane for a flat or low-slope roof in San Francisco when grease, chemicals or a long life decide the job. Plan on $10 to $16 per square foot installed at 60 mil, 25 to 30 years of life, and a permit at $514 and up. Get three written quotes that name the thickness, the separation layer and the tapered plan. On a clean roof, get a TPO price too.
NAICS Code 238160 – Roofing Contractors. Call +1 833-804-6249 for a detailed inspection.
